Wipers

Molded in nitrile, this double lipped wiper is common in Toyota lift trucks.

Nitrile Material | 35 MM Inner Diameter | Wiper

15 X 16 X 1/2 D Wiper

Each Seal Guard Wiper consists of two flexible bronze rings which are held in place by a nitrile cushion ring. The cushion ring absorbs side loads and energizes the wiper to maintain close contact with the rod. Particularly suited for hostile environments, seal guard wipers shave off sand, grift, slag, flux, paint, moisture, chips and slivers. Seal Guard Wipers are long-lasting, self-adjusting, and offer low friction. Seal Guard Wipers can be installed in standard Hercules® Sealing Products “ST” or “D” Style grooves by increasing the “F” gland dimension to the “F” Throat Diameter shown.

70A Durometer | 660 Bronze; Nitrile Material | 1 1/2 in Nominal Inner Diameter | Wiper

RWS, 2 X 2 1/2 X 1/4 Seal-Guard FKM

Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.

90A Durometer | Urethane Material | 8 in Nominal Inner Diameter

Features

• Flexible enough to snap into a groove
• Wipers are constructed of fluorocarbon

RW-95URE/NBR-5.500×6.250×0.375

Wipers are installed in hydraulic cylinders to prevent dirt, dust, and moisture from entering the cylinder as they retract back into the system. A hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components.

Buna-N Material | 1 1/4 in Nominal Inner Diameter

Features

• Installed in hydraulic cylinders to prevent dirt, dust, and moistures
• Hydraulic wiper prevents contamination that could damage wear rings, seals, and other cylinder components

Style ST wiper rings are precision molded from 90A durometer urethane. Flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications. “V” tagged wipers are constructed of fluorocarbon.

90A Durometer | Fluorocarbon Material | 1 1/4 in Nominal Inner Diameter

Features

• Flexible enough to snap into a groove
• Wipers are constructed of fluorocarbon

Single-lipped, snap-in rod wiper is designed to fit D-style housings.

The ST-XLF wipers are designed to fit the standard ST wiper groove. These wipers include a dust lip to prevent contaminates from entering through the groove. They also have a ribbed inside diameter for low friction operation and to prevent pressure traps between the wiper and rod seal. Developed specifically for use in harsher environments with heavy contamination, such as in agriculture, off-highway, and forestry equipment.

Urethane Material | 1 1/2 in Nominal Inner Diameter

Features

• Precision trimmed wiping lip
• Retrofits most ‘D’ wiper housings
• Especially effective in vertically mounted cylinders
• Designed to follow the rod deflection caused by side loads
• Interchangeable with Hallite 520 wiper
• Sharp wiping lip scrapes heavy contamination from rod protecting sealing system
• Umbrella Wiper Technology™ protects housing from contamination and reduces moisture ingress

Each Seal Guard Wiper consists of two flexible bronze rings which are held in place by a nitrile cushion ring. The cushion ring absorbs side loads and energizes the wiper to maintain close contact with the rod. Particularly suited for hostile environments, seal guard wipers shave off sand, grift, slag, flux, paint, moisture, chips and slivers. Seal Guard Wipers are long-lasting, self-adjusting, and offer low friction. Seal Guard Wipers can be installed in standard Hercules® Sealing Products “ST” or “D” Style grooves by increasing the “F” gland dimension to the “F” Throat Diameter shown.

70A Durometer | 660 Bronze; Nitrile Material | 1 in Nominal Inner Diameter | Wiper