U-seals, Polypaks, U-cups

Top-of-the-range twin lip rod seal designed to provide a dry sealing solution in heavy-duty applications. The seal’s shell is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. Featuring high pressure and high shock load capability, this seal utilizes the same twin lip design found in Hercules®, Sealing Products’ RTU style. With the main body of the seal molded from high performance polyurethane, this seal, incorporates a dynamically designed nitrile energizer and a tough polyacetal anti-extrusion ring. RTUB is capable of, pressures up to 10,000 psi in approved applications.

94A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

Utilizing the same profiles as the Style 800 Polyurethane U-Seal line, these u-seals are molded from a fluorocarbon, compound. While being compatible with a broader range of fluids, these fluorocarbon seals will also operate, continuously at temperatures from -20° to +400 °F. NOTE: If you are not sure of fluid/seal compatibility, please refer, to the fluid compatibility chart in the appendix or contact our Engineering Department.

95A Durometer | Fluorocarbon Material | 2 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

The Z-Seal™ is a squeeze type seal, combining the excellent sealability and low compression set of a resilient rubber lip with the greater anti-extrusion characteristics of a hard thermoplastic base. Under low pressure conditions, the sealing lip provides its own compressive seal force. As pressure increases, hydrostatic pressure is mechanically transmitted through the elastomeric seal element into the anti-extrusion base. The applied force then deflects radially in a controlled manner, closing the extrusion gap behind the sealing lip. Under this condition, maximum sealing effectiveness is achieved.

95A 70A Durometer | Urethane Nitrile Rubber Material | 2 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Z-Seal

Utilizing the same profiles as the Style 800 Polyurethane U-Seal line, these u-seals are molded from a fluorocarbon, compound. While being compatible with a broader range of fluids, these fluorocarbon seals will also operate, continuously at temperatures from -20° to +400 °F. NOTE: If you are not sure of fluid/seal compatibility, please refer, to the fluid compatibility chart in the appendix or contact our Engineering Department.

95A Durometer | Fluorocarbon Material | 3 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 32 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

These seals are specifically designed with a second lip on their inside diameter and engineered to attain maximum, life and reliability in dynamic rod sealing. This feature results in reduced leakage, less friction, increased stability, and, prevents air and contaminants from entering the cylinder.

92A Durometer | Urethane Material | 2 3/4 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 28 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 30 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 45 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

Style 870 u-seals are precision molded from Buna-N synthetic rubber. Style 870 u-seal numbers conform in size to Army-Navy specification AN6226.

70A Durometer | Buna-N Rubber Material | 3 1/4 in Nominal Inner Diameter | U-Seal