Piston Seals

Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split backups for extrusion resistance, and two split bearing rings. No further support bearings are required.

90A Durometer | Nitrile Material | 1 3/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Our Style PSU piston seal, or uniring, is a laminated one piece double acting seal made of cast polyurethane. The tough outer layer is highly resistant to abrasion and is impregnated with molybdenum disulfide to reduce friction. The softer inner layer acts as a static seal and also energizes the OD to make full contact with the bore. This seal may be used to replace an existing Uniring or other seals of the same dimensions – O-rings, O-rings with back-ups, T-seals, U-seals, etc. Piston diameter “I” dimensions are given for pistons without wear rings.

60D & 57A Durometer | Urethane Composite Material | 3 1/2 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

A heavy duty double-acting assembly, the capped piston T-seal exhibits excellent sealability, extrusion resistance, and wearability. T-seals with “BR” suffix utilize a Bronze Filled PTFE cap instead of the standard Glass Filled PTFE cap.

PTFE; Nylon; Rubber Material | 4.942 in Nominal Inner Diameter | Capped Piston T-Seal

Features

• Glass-filled PTFE cap, nylon back-up, rubber energizer

Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 2.353 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 2 3/16 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Piston diameter “I” dimensions are given for pistons without wear rings.

15% Glass Filled PTFE Material | 3.103 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

This seal, molded from high grade 55D polyurethane, may retrofit the PS1800 seals, considering all dimensions are comparable. This seal material, with a high degree of memory, stretches over the piston and snaps in the groove for immediate assembly. These seals also feature low friction and high abrasion and extrusion resistance which helps to eliminate assembly damage. Piston diameter “I” dimensions are given for pistons without wear rings.

55D Durometer | Glass/PTFE Filled Polyurethane Material | 6 1/4 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

This two piece piston seal design comes made with a heat-stabilized, thermoplastic step-cut ring along with a profiled NBR energizer. This product offers extreme strength and resistance to extrusion, a very high resistance to abrasion, and ease of installation thanks to the step cut design and chamfered edges. The design also allows the seal to pass over ports without damage and offers greater resistance to surface roughness in comparison to any elastomer seals. The profiled energizer offers improved dynamic sealing ability, responding quickly to pressure changes and providing excellent sealing characteristics under a wide range of pressure conditions.

Glass Filled Nylon Material | 3.908 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

This capped piston seal consists of a filled PTFE cap, a T-shaped NBR energizer, and two split nylon backup rings. It exhibits low friction, high sealability, and excellent resistance to extrusion and wear.

PTFE Material | 105 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

A double acting piston seal with many features: Two compact seal edges to concentrate the load against the dynamic surface, a cavity between the two external seal edges to retain fluid (reducing friction and wear), side grooves to allow pressure to load the energizer in all working conditions, high sealing performance at low pressure, excellent wear-resistance, and high resistance against extrusion.

97A; 70A Durometer | Urethane Material | 49 MM Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities