Search Results
Filter Your Search
Category Group
Shop by Category
MHT-40X50 has a wall thickness of 5 mm. The ID is 40 mm and the OD is 50 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $4.29 |
| 15-74 | $3.33 |
| 75-104 | $3.00 |
| 105+ | $2.73 |
100mm induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $26.22 |
| 15-29 | $18.75 |
| 30-59 | $16.39 |
| 60-119 | $13.11 |
| 120+ | $11.93 |
Designed to fit on one or two piece pistons, this piston seal employs a nitrile seal for high sealability, nylon split back-ups for extrusion resistance, and two split bearing rings. No further support bearings are required.
70A Durometer | NBR Material | 34 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
HT-6500X6000 has a wall thickness of 0.25 in. The ID is 6 in and the OD is 6.5 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.55 |
| 15-59 | $7.47 |
| 60-89 | $6.63 |
| 90-119 | $5.98 |
| 120+ | $5.44 |
HWT-4000X2000 has a wall thickness of 1 in. The ID is 2 in and the OD is 4 in. The material is 1026 Carbon Steel.
Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-4 | $14.74 |
| 5-24 | $12.88 |
| 25-49 | $11.44 |
| 50+ | $10.31 |
TR-500 has a 0.5 in diameter. The material is 1144 Carbon Steel, which is equivalent to Stressproof tie rod.
Tie rods are sold in 12 ft. lengths only. Rods can be cut for UPS shipment or left whole, if necessary. Freight charges may vary depending on required length.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
ALHT3250X3000 has a 0.125 in wall thickness. The ID is 3 in and the OD is 3.25 in. The material is 6063-T832 Aluminum.
Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.
6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).
- No machining required on the ID
- Seamless extruded and cold-drawn
- Hard coated interior
- Corrosion resistance
- Good weldability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $5.86 |
| 15-29 | $4.69 |
| 30-104 | $3.35 |
| 105+ | $2.60 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 3 1/2 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 1 3/4 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
