Search Results

HC-6500-12 has a 7.5 in OD and is made to fit a 6 in bore cylinder.

Head cap size is determined based on the bending stress.

A static seal or o-ring is used in between the head cap and barrel (except welded construction).

The main function of the head cap is to enclose the pressure chamber at one end. The cap is connected to the cylinder body by means of welding, threading, bolts, or tie rod.

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 30 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation

*
4.5 in Hot Finished 1018 Carbon Steel*
round bar. Material can be cut to any size.

Suitable for shafting and applications that do not require the greater strength of high carbon and alloy steels.

• Good case hardening properties
• Fair machinability
• Readily brazed and welded

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

90 Durometer | Buna-N Rubber Material | 11/16 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

Solid Urethane backup ring with a flat cross-section.

95A Durometer | Urethane Material | 4 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

• High strength and abrasion resistance
• Wide temperature range
• Chemical resistance
• Low friction
• Easy installation

CIHT2740X2500 has a wall thickness of 0.1 in. The ID is 2.5 in and the OD is 2.74 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

1 in clevis pin with 0.048 in grooves machined into each end to fit two retaining rings. Retaining rings are not included.

Pivot pins with grooves are meant to be used on a hydraulic cylinder that extends and retracts a telescoping lift arm.

HT-3750X3000 has a wall thickness of 0.375 in. The ID is 3 in and the OD is 3.75 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

HWT-3500X1500 has a wall thickness of 1 in. The ID is 1.5 in and the OD is 3.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

HWT-7000X4000 has a wall thickness of 1.5 in. The ID is 4 in and the OD is 7 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.