Search Results
Filter Your Search
Category Group
Shop by Category
1 in induction hardened chrome shafting.
The base material is 4140 Alloy Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $24.35 |
| 15-29 | $16.22 |
| 30-89 | $12.18 |
| 90-134 | $10.81 |
| 135+ | $9.74 |
1.625 induction hardened chrome shafting.
The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).
Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.
- Greater strength
- Better resistance to mechanical damage
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $8.52 |
| 15-29 | $5.68 |
| 30-89 | $4.06 |
| 90-134 | $3.15 |
| 135+ | $2.84 |
Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.
92A Durometer | Urethane Material | 2 in Nominal Inner Diameter
Features
- Used in Heavy Duty U-seals
- Capable of surviving hostile environments
- Molded from the high performance urethane
Molded from tough, wear resistant 55D polyester, these seals are for light to medium duty applications and are interchangeable with the style MPS seals of the same dimensions. Nitrile rings are used for energizers.
55D; 70A Durometer | Polyester Material | 52 MM Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 2 5/16 in Nominal Inner Diameter | 3/32 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
CPOD2000X1250 has a wall thickness of 0.375 in. The ID is 1.25 in and the OD is 2 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $6.20 |
| 15-29 | $5.16 |
| 30-59 | $3.88 |
| 60-104 | $3.44 |
| 105+ | $3.10 |
CPOD3000X2250 has a wall thickness of 0.375 in. The ID is 2.25 in and the OD is 3 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $14.14 |
| 15-29 | $11.77 |
| 30-59 | $8.84 |
| 60-104 | $7.85 |
| 105+ | $7.07 |
Split Nylon backup ring with a flat cross-section.
Nylon Material | 2 1/2 in Nominal Inner Diameter | 1/4 in Cross Section | Backup Ring
Features
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
