Search Results
Filter Your Search
Category Group
Shop by Category
MHT-95X115 has a wall thickness of 10 mm. The ID is 95 mm and the OD is 115 mm. The material is 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $13.05 |
| 15-44 | $10.13 |
| 45-104 | $9.12 |
| 105+ | $8.30 |
Parback® backup ring with a curved cross-section.
Parbaks are contoured on one face to minimize distortion of the o-ring when under pressure. Parbaks should be installed with the contoured face against the o-ring, but reversal does no harm.
90A Durometer | Buna-N Rubber Material | 1 13/16 in Nominal Inner Diameter | 3/32 in Cross Section | Backup Ring
Features
- Excellent extrusion resistance
- Easily stretched for installation
- Lubrication is enhanced by rubber which absorbs system fluid and does not plate out on rubbing surfaces
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 5 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 6 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
Hercules® Sealing Products is pleased to introduce our new line of PowerbandTM tight tolerance premium wearrings. Manufactured from a highly engineered blend of premium nylon, glass fiber, and PTFE, PowerbandsTM offer a high strength wear-ring for all cylinder applications, including those with minimal lubrication. And, with a Coefficient of Friction nearly 50% lower than our standard product, your cylinders will run smoother and more efficiently than ever. All PowerbandsTM are fully machined with cross-section tolerances of only ±0.001”, chamfered corners, and scarf or angle-cut end gaps. Compared to standard tolerances of ±0.0025”, this tightened tolerance improves the alignment and concentric operation of cylinder rods and pistons. The fully machined chamfered corners will better accommodate cylinder housing grooves, further improving piston and rod alignment. Lastly, the scarf-cut end gap reduces the loss of bearing support that may occur during cylinder side-loading. When combined, these features reduce the tolerance stack-up within the components of the cylinder. As a result, your cylinders will operate more consistently and be capable of operating at higher pressures and higher side loads than with standard wear-ring products. Furthermore, with this improved cylinder operation, your seals will last longer and the life of your cylinder will be extended. PowerbandsTM are currently available in our most popular wear-ring dimensions.
1 3/4 in Nominal Inner Diameter | Powerband
Features
- PowerbandsTM offer a high strength wear-ring for all cylinder applications
- Fully machined with cross-section tolerances of only ±0.001
- Chamfered corners
- Scarf or angle-cut end gaps
Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.
94A Durometer | Urethane Material | 7 in Nominal Inner Diameter
Features
- Crush lip to provide extra interference
- Bead on the shoulder to keep contaminants out
- Ribbed ID to prevent pressure traps
SB76ES has a 3 in ID.
The bushing is Unsealed and made of forged steel. The ball will swivel like a fish eye with 3-5 degrees of movement.
CPO-1062 has a 1.062 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.
ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.
- Extremely smooth surface finish
- Excellent wear and corrosion resistance
- Good strength and impact properties
- Good machinability
- Reasonable weldability
- Fair response to normal heat treating and induction hardening practices
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-29 | $5.42 |
| 30-74 | $2.32 |
| 75-104 | $2.03 |
| 105+ | $1.80 |
This U-cup style buffer ring offers an asymmetric sealing lip profile, chamfered sealing edges, and pressure relieving capabilities to prevent inner pressure entrapment when employed in a tandem sealing system. This rod buffer seal is designed to absorb impact pressure fluctuations under high-load conditions thus increasing the life of the primary seal.
Urethane Material | 3 in Nominal Inner Diameter | Buffer Seal
HC-3500-12 has a 4 in OD and is made to fit a 3 in bore cylinder.
Head cap size is determined based on the bending stress.
A static seal or o-ring is used in between the head cap and barrel (except welded construction).
The main function of the head cap is to enclose the pressure chamber at one end. The cap is connected to the cylinder body by means of welding, threading, bolts, or tie rod.
