Search Results

Hytrel backup ring with a flat cross-section.

Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.

55D Durometer | Hytrel Material | 1 1/2 in Nominal Inner Diameter | 0.11 in Cross Section | Backup Ring

Features

• Improved extrusion resistance compared to standard FKM or NBR backups
• Can be stretched over larger diameters and will return quickly to their original size
• High strength and abrasion resistance
• Wide temperature range
• Chemical resistance
• Low friction
• Easy installation

HT-8750X8000 has a wall thickness of 0.375 in. The ID is 8 in and the OD is 8.75 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

HWT-6000X4000 has a wall thickness of 1 in. The ID is 4 in and the OD is 6 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

2.125 in induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

20mm induction hardened chrome shafting.

The base material is 1045/1050 Carbon Steel with 0.0005 in (0.0127mm minimum)-thick chrome plating and a case depth of 0.05 in (1.27 mm).

Induction Hardened Chrome is typically used in abrasive envrionments where the cylinder is exposed to rocks or heavy debris. Also used to machine clevis pins.

• Greater strength
• Better resistance to mechanical damage

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

JD-50MM-IT

Cast Iron Rod Clevis Mount with a 2.5 in – 12 TPI threaded end and a 3 in pin hole.

Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.

SS17-4/CPO-0625 has a 0.0625 in diameter. The material is 17-4 Stainless Steel with Standard Chrome on the exterior.

Commonly used in offshore cranes, marine cylinders, and marine steering cylinders.

• Highest level of corrosion resistance

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

CIHT5235X5000 has a wall thickness of 0.1175 in. The ID is 5 in and the OD is 5.235 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.

Nylon Material | 2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring

Features

• Protection Against Wear
• Reduced Friction
• Extended Cylinder Life
• Operational Efficiency