Search Results

WR-NYL, 6 X 1/2 Wear Ring

Solid Urethane backup ring with a flat cross-section.

95A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | Backup Ring

Features

• High strength and abrasion resistance
• Wide temperature range
• Chemical resistance
• Low friction
• Easy installation

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 3 in Nominal Inner Diameter | 1/4 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.

90A Durometer | Urethane Material | 1 3/8 in Nominal Inner Diameter

Features

• Flexible, snap-in design for easy installation into closed housings
• Low compression set

Hytrel backup ring with a flat cross-section.

Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.

55D Durometer | Hytrel Material | 5 5/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring

Features

• Improved extrusion resistance compared to standard FKM or NBR backups
• Can be stretched over larger diameters and will return quickly to their original size
• High strength and abrasion resistance
• Wide temperature range
• Chemical resistance
• Low friction
• Easy installation

CPO-3250 has a 3.25 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

CPOD3500X2500 has a wall thickness of 0.5 in. The ID is 2.5 in and the OD is 3.5 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

CPOD4000X3500 has a wall thickness of 0.25 in. The ID is 3.5 in and the OD is 4 in. The material is 1026 Carbon Steel with chrome plating on the Outside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

Molded in a tough urethane, this seal employs an additional lip near the heel. The twin lip design provides stability, friction-reducing lube retention, and some contaminant resistance. VME – Secondary lip is further from heel than standard MRTU. NOTE: E = European Urethane.

Urethane Material | 35 MM Nominal Inner Diameter | Rod U-Seal

Features

• Excellent low temperature performance
• Easy installation