Search Results

Utilizing tough polyurethane, these seals possess excellent wear and abrasion resistance. Symmetrical in design, they can be used in rod or piston applications. E= European Urethane.

Urethane Material | 25 MM Nominal Inner Diameter | U-Seal

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 2 7/8 in Nominal Inner Diameter | 1/16 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

90 Durometer | Buna-N Rubber Material | 3 1/4 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

CIHT2240X2000 has a wall thickness of 0.12 in. The ID is 2 in and the OD is 2.24 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

ALHT4750X4500 has a 0.125 in wall thickness. The ID is 4.5 in and the OD is 4.75 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

• No machining required on the ID
• Seamless extruded and cold-drawn
• Hard coated interior
• Corrosion resistance
• Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

DE-07 is a standard rod eye machined from Cast Iron.

A rod eye is a type of mount attached to the end of the cylinder rod. This connects to a mounting point on the machine and usually incorporates a bearing to allow for some movement.

HT-4250X3500 has a wall thickness of 0.375 in. The ID is 3.5 in and the OD is 4.25 in. The material is DOM 1026 Steel – ST52.3 and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

HWT-6500X3500 has a wall thickness of 1.5 in. The ID is 3.5 in and the OD is 6.5 in. The material is 1026 Carbon Steel.

Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

ALUM-7000 has a 7 in diameter. The material is 6061 Aluminum T6

6061 Aluminum T6 is suitable for machining pistons and head glands.

The T6 refers to the temper or degree of hardness. T6 has been solution heat treated and artificially aged to provide the maximum yield strength for a 6061 aluminum alloy.

• Heat treated and aged for increased strength
• Easily formed
• Weldable
• Corrosion resistant

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

0.75 in clevis pin with two 0.14 in holes that can be used to retain the pin with cotter pins or locking pins. Cotter pins not included.