Search Results
Filter Your Search
Category Group
Shop by Category
HT-9250X8000 has a wall thickness of 0.625 in. The ID is 8 in and the OD is 9.25 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-14 | $25.80 |
| 15-59 | $22.91 |
| 60-89 | $20.64 |
| 90+ | $18.78 |
The Hallite 533 is capable of withstanding high side loads and preventing metal-to-metal contact between the piston and the bore or the rod and the gland.
The PA 533 material is heat stabilised 33% glass reinforced nylon 66, which offers excellent bearing properties.
Compatible with hydraulic and lubricating oils. The PA 533 material is not recommended for use in water based fluids (HFA) or where significant water is present, due to the swell of the nylon.
AN wipers are ideal for light duty and pneumatic applications. Its main purpose is to prevent dirt and contaminants from entering the hydraulic or pneumatic systems. Suffix “SH” designates slotted heel design, “V” designates fluorocarbon material, and “B” designates carboxilated nitrile material.
90A Durometer | Urethane Material | 4 1/2 in Nominal Inner Diameter
Features
- Flexible, snap-in design for easy installation into closed housings
- Low compression set
Hytrel backup ring with a flat cross-section.
Molded of 55D Durometer Hytrel, these back-up rings provide excellent extrusion resistance and tolerance to fluids such as phosphate esters, hydraulic oil and water. Stretched for installation, they return quickly to their original size for easy installation.
55D Durometer | Hytrel Material | 2 1/8 in Nominal Inner Diameter | 3/16 in Cross Section | Backup Ring
Features
- Improved extrusion resistance compared to standard FKM or NBR backups
- Can be stretched over larger diameters and will return quickly to their original size
- High strength and abrasion resistance
- Wide temperature range
- Chemical resistance
- Low friction
- Easy installation
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70 Durometer | Buna-N Rubber Material | 5 3/4 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring
Features
- Pressure range varies according to diametral clearance
- Temperature range of -40 °F to -240 °F
DUCT-3000 has a diameter of 3 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-9 | $14.57 |
| 10-19 | $9.71 |
| 20-39 | $7.29 |
| 40+ | $6.47 |
Molded in urethane, this wiper is flexible enough to easily snap into a groove yet tough enough to handle difficult rod wiping applications.
Urethane Material | 30 MM Inner Diameter | Wiper
DUCT-4500 has a diameter of 4.5 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-9 | $18.58 |
| 10-39 | $14.42 |
| 40+ | $11.82 |
O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.
70A Durometer | Nitrile Material | 60 MM Nominal Inner Diameter | 3 MM Cross Section | O-Ring
Features
- Chemical resistance
- Temperature range of -40 °F to 220 °F
