Search Results
Filter Your Search
Category Group
Shop by Category
HWT-6500X3500 has a wall thickness of 1.5 in. The ID is 3.5 in and the OD is 6.5 in. The material is 1026 Carbon Steel.
Heavy Wall Tubes are used for machining high strength and close tolerance parts like bushings, axles, hydraulics, and sleeves.
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-4 | $23.68 |
| 5-14 | $20.70 |
| 15-24 | $18.38 |
| 25-49 | $16.56 |
| 50+ | $15.07 |
The PS1800 provides low friction, high strength piston sealing. The PS1800 also provides double-acting piston sealing in a compact design that meets the requirements of ANSI/B93-32-1973. Piston diameter “I” dimensions are given for pistons without wear rings.
15% Glass Filled PTFE Material | 1 11/16 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.
93A; 70A Durometer | Urethane Material | 5 1/2 in Nominal Inner Diameter | Piston Seal
Features
- Easy assembly
- Low friction capabilities
Utilizing tough polyurethane, these seals possess excellent wear and abrasion resistance. Symmetrical in design, they can be used in rod or piston applications. E= European Urethane.
Urethane Material | 25 MM Nominal Inner Diameter | U-Seal
Steel Rod Clevis Mount with a 1 in – 14 TPI threaded end and a 1 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
Cast Iron Rod Clevis Mount with a 0.4375 in – 20 TPI threaded end and a 0.5 in pin hole.
Clevis mounts help maintain alignment and protect the cylinder from side load. Mounts attach to threaded stud ends, pivot holes, or bolt holes on the cylinder. Can be used with hydraulic cylinders with standard bore sizes.
Wear rings provide a hard-wearing surface that protects the cylinder walls and the piston rod from scoring and abrasion. By maintaining alignment and reducing side loads, these rings facilitate smoother piston movement and lower friction levels.
Nylon Material | 1 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | Wear Ring
Features
- Protection Against Wear
- Reduced Friction
- Extended Cylinder Life
- Operational Efficiency
DUCT-6000 has a diameter of 6 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-9 | $28.60 |
| 10-39 | $25.40 |
| 40+ | $20.82 |
DUCT-5000 has a diameter of 5 in. The material is 65-45-12 Ductile Iron.
65-45-12 Ductile Iron is used to machine pistons, glands, caps, manifolds, rams, and valve bodies.
Ductile has higher machining speeds than steel and there is usually no need for deburring machined parts. The graphite flakes in the material act as a self-lubricant. Ductile can be flame or induction hardened as well as deep hardened.
Ductile bars are produced with sufficient stock on the outside diameter to ensure clean-up at the nominal dimension.
- Excellent machinability
- Optimal impact strengths
- Optimal fatigue properties
- Optimal electrical conductivity
- High magnetic permeability
Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.
| 1-9 | $22.81 |
| 10-39 | $17.70 |
| 40+ | $14.51 |
Style ST-XL wipers are molded from premium urethane and are direct replacements for Style “ST” or “D” wipers. The outside diameter of the ring has a crush lip providing extra interference in the groove. A bead on the shoulder stops contaminates from entering through the groove. The inside diameter is ribbed to prevent pressure traps between the wiper and rod seal.
94A Durometer | Urethane Material | 2 1/4 in Nominal Inner Diameter
Features
- Crush lip to provide extra interference
- Bead on the shoulder to keep contaminants out
- Ribbed ID to prevent pressure traps
