Search Results

HT-2000X1500 has a wall thickness of 0.25 in. The ID is 1.5 in and the OD is 2 in. The material is DOM 1026 Carbon Steel and has been stress-relieved and annealed.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

Utilizing a sturdy metal case, these wipers are molded from the same high performance urethane used in our Heavy Duty U-seals. Built for severe service, these wipers are capable of surviving hostile environments.

92A Durometer | Urethane Material | 1 in Nominal Inner Diameter

Features

• Used in Heavy Duty U-seals
• Capable of surviving hostile environments
• Molded from the high performance urethane

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 2 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 5 in Nominal Inner Diameter | 3/32 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

Molded from 93 Shore A polyurethane with a 70 Shore A energizer, this seal utilizes the same groove dimensions as a standard o-ring or T-seal. One or two Style 575 back-up rings may be used for wider grooves. Extrusion resistant by design, this seal is also resistant to rolling and twisting. Installation is an easy two step snap-in procedure with no need to re-size before insertion into the bore. Piston diameter “I” dimensions are given for pistons without wear rings.

93A; 70A Durometer | Urethane Material | 2 5/8 in Nominal Inner Diameter | Piston Seal

Features

• Easy assembly
• Low friction capabilities

Asymmetric rod seal designed with precision trimmed sealing lips to provide a dry sealing solution in light and medium-duty applications. The Hallite 605 is molded in Hythane® 181, Hallite’s high-performance polyurethane, for easy installation and excellent low temperature performance. The twin lip design helps solve difficult rod sealing problems by providing lower friction, increased stability, and high, dynamic lip force, while preventing air penetration from outside the cylinder. Designed to have interference in the seal housing groove and has a secondary lip. The secondary sealing lip located behind the primary sealing lip improves stability of the seal in the gland. The inner dynamic lip is shorter and more robust to improve sealing and compression set characteristics over conventional, symmetrical U-seals.

The seal can be considered for use in heavy-duty applications when used with a suitable full depth back-up ring. The sealing lips are precision trimmed at an angle to give optimal rod sealing performance.

94A Durometer | Urethane Material | 1 1/2 in Nominal Inner Diameter | 3/16 in Cross Section | U-Seal

Features

• General purpose rod seal
• Robust design
• Excellent wear resistance
• Increase seal stability
• Performs well over wide temperature range and is extremely effective in low temperatures
• Primary lip protection
• Easy to install

CPO-1125 has a 1.125 in diameter with Standard Chrome. The base material is 1045 Carbon Steel with a yield strength of 75,000 psi.

ASTM A108 is the most commonly used and economical grade of shafting for hydraulic cylinder components, blower shafts, and mandrels.

• Extremely smooth surface finish
• Excellent wear and corrosion resistance
• Good strength and impact properties
• Good machinability
• Reasonable weldability
• Fair response to normal heat treating and induction hardening practices

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

O-rings as elastic loops that seal static and dynamic applications. They are used to seal the space between cylinders, pistons, pipes and tubes and can be made from various materials.

70 Durometer | Buna-N Rubber Material | 7 1/2 in Nominal Inner Diameter | 1/8 in Cross Section | O-Ring

Features

• Pressure range varies according to diametral clearance
• Temperature range of -40 °F to -240 °F

CIHT6375X6000 has a wall thickness of 0.1875 in. The ID is 6 in and the OD is 6.375 in. The material is 1026 Carbon Steel with chrome plating on the Inside Surface.

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.

ALHT3750X3500 has a 0.125 in wall thickness. The ID is 3.5 in and the OD is 3.75 in. The material is 6063-T832 Aluminum.

Seamless extruded and cold-drawn. Hard coated on the ID which gives the aluminum tube a tough, abrasive-resitant surface.

6063-T832 Aluminum is used for pneumatic cylinder applications requiring very good corrosion resistance and/or light weight. Can also be used for low-pressure oil cylinders (250 psi or less).

• No machining required on the ID
• Seamless extruded and cold-drawn
• Hard coated interior
• Corrosion resistance
• Good weldability

Full mill lengths will be cut to lengths between 12 ft and 19 ft long. Packages longer than 44 inches may have additional freight charges.